New boat expectations
Moderators: Redneck_Randy, badmoonrising, lakerunner
New boat expectations
By no means am I a mechanic or expert, but have been around long enough to learn a few things, so I like to try and fix things myself, when possible...
I have had my boat for about 7-8 months now. I use mine both in salt and brackish water.
The very large river by me quite often can get pretty choppy when the wind whips up, actually can get very rough, but I avoid those days.
So the boat gets "challenged" versus smaller smooth lakes.
I have found that many of the screws that hold door hinges as well as other screws, are backing out.
When tightening them up, I find some of them are actually stripped.
Rather than just using one size larger screw to repair, I have through bolted some of them with Teflon locking nuts.
Hauling it back to the dealer to fix these issues just seems ridiculous to me?????? I am sure they would just use a larger screw????
Just curious, does everyone else have these same issues??? BTW, mine is a Harris, which should be a pretty well built boat.
Thanks
I have had my boat for about 7-8 months now. I use mine both in salt and brackish water.
The very large river by me quite often can get pretty choppy when the wind whips up, actually can get very rough, but I avoid those days.
So the boat gets "challenged" versus smaller smooth lakes.
I have found that many of the screws that hold door hinges as well as other screws, are backing out.
When tightening them up, I find some of them are actually stripped.
Rather than just using one size larger screw to repair, I have through bolted some of them with Teflon locking nuts.
Hauling it back to the dealer to fix these issues just seems ridiculous to me?????? I am sure they would just use a larger screw????
Just curious, does everyone else have these same issues??? BTW, mine is a Harris, which should be a pretty well built boat.
Thanks
I am the guy at the boat ramp that gives you dirty looks when you are a complete idiot and too stupid to know it.
- lakerunner
- Site Moderator
- Posts: 4820
- Joined: Fri Mar 17, 2006 2:31 pm
- Location: Live in McAlester, Ok Boat on Tenkiller
- Contact:
Re: New boat expectations
All my hinges are riveted. I think your fix is the way to go
Loyd & Betty Meeks
Livin the lake life
2004 Tracker 22 Regency/2010 90 E-Tec. Pulled by Ford 2020 F 250,
McAlester, Oklahoma
Home lake is Tenkiller
Livin the lake life
2004 Tracker 22 Regency/2010 90 E-Tec. Pulled by Ford 2020 F 250,
McAlester, Oklahoma
Home lake is Tenkiller
Re: New boat expectations
Riveting makes some sense. Didn't even think of that one...and I own two riveting tools. I may try that on the next one for shits and giggles. Thx
I am the guy at the boat ramp that gives you dirty looks when you are a complete idiot and too stupid to know it.
Re: New boat expectations
Rip,
I think high quality stainless bolts with teflon locking nuts would be the way to go. GOOD SOLUTION !!!!
Think I would prefer to rivets....
I think high quality stainless bolts with teflon locking nuts would be the way to go. GOOD SOLUTION !!!!
Think I would prefer to rivets....
Re: New boat expectations
I know the through bolts are a permanent fix. Rivets might look a little prettier.
I may do some of both. Top, center and bottom of door hinge through bolt and ones between those rivet.
Thanks guys.
I may do some of both. Top, center and bottom of door hinge through bolt and ones between those rivet.
Thanks guys.
I am the guy at the boat ramp that gives you dirty looks when you are a complete idiot and too stupid to know it.
Re: New boat expectations
Say it aint so...I have a Harris 210 on order.
Any other problems?
ksks
2019 Harris 210 with 150 hp Merc
Re: New boat expectations
Ask your dealer to come to you to fix these issues. When I got my new boat, a couple of minor issues popped up about a month after delivery. My boat was in a slip an hour and a half from the dealer (they delivered it to me there), and they happily sent a tech to my slip to fix it. He spent three hours driving to spend 30 minutes fixed a couple of things.
I've said it before and I'll say it again............."pick the dealer, then pick the boat!"
Steve
"Serendipity" - 2017 Sweetwater 2286 WB Tritoon w/ 150HP Yamaha
Slipped at Lake Anna, Virginia
Primary Residence: Richmond, Virgina
Lake House: Lake Anna, Virginia
"Serendipity" - 2017 Sweetwater 2286 WB Tritoon w/ 150HP Yamaha
Slipped at Lake Anna, Virginia
Primary Residence: Richmond, Virgina
Lake House: Lake Anna, Virginia
Re: New boat expectations
[/quote]Say it aint so...I have a Harris 210 on order.
Any other problems?
[/quote]
Love my boat, this has really been the only issue boat wise.
My motor drove me crazy, they had the speedo set wrong (mercury)so I ended up buying mercury "vessel view" to
tell me exactly what was going on and that fixed that. Dealer was no help at all.
They switched out the prop, put I wrong hub, I could go on and on about the trouble that was.
Now all is good with motor.
Any other problems?
[/quote]
Love my boat, this has really been the only issue boat wise.
My motor drove me crazy, they had the speedo set wrong (mercury)so I ended up buying mercury "vessel view" to
tell me exactly what was going on and that fixed that. Dealer was no help at all.
They switched out the prop, put I wrong hub, I could go on and on about the trouble that was.
Now all is good with motor.
I am the guy at the boat ramp that gives you dirty looks when you are a complete idiot and too stupid to know it.
Re: New boat expectations
steve1313 wrote: ↑Sun Feb 03, 2019 3:45 amI had a Bennington dealer 3 miles from me but liked some features on the Harris so much more. I picked a dealer 30 miles away.
Horrible decision on my part. But extremely happy now, so a little pain for a couple of months but did get the boat I wanted.
Next time I will choose dealer over boat.....if there ever is a next time.
I am the guy at the boat ramp that gives you dirty looks when you are a complete idiot and too stupid to know it.
Re: New boat expectations
If the dealer is only 30 miles away, I'd definitely have them come to you!
Steve
"Serendipity" - 2017 Sweetwater 2286 WB Tritoon w/ 150HP Yamaha
Slipped at Lake Anna, Virginia
Primary Residence: Richmond, Virgina
Lake House: Lake Anna, Virginia
"Serendipity" - 2017 Sweetwater 2286 WB Tritoon w/ 150HP Yamaha
Slipped at Lake Anna, Virginia
Primary Residence: Richmond, Virgina
Lake House: Lake Anna, Virginia
Re: New boat expectations
Check the screws you think stripped because my Harris uses threaded studs with a binding barrel and you may have lost the barrel on the bottom side. I called my Harris parts guy and they sent me a dozen. They know the exact size you need too.
What came loose on my Solstice had more to do with those holding the bimini hinges. I've since given all the loose ones a touch of Locktite.
It's good to go over your entire boat and check for loose screws.
What came loose on my Solstice had more to do with those holding the bimini hinges. I've since given all the loose ones a touch of Locktite.
It's good to go over your entire boat and check for loose screws.
Michael and Laura
'12 Ford F150 Lariat SuperCrew Ecoboost
'14 Harris Solstice 220, P3 tritoon, Mercury Verado 150, Enertia 14p.
prior boat: '02 Century 2600CC, twin Yamaha EFI 200's, full instruments.
'12 Ford F150 Lariat SuperCrew Ecoboost
'14 Harris Solstice 220, P3 tritoon, Mercury Verado 150, Enertia 14p.
prior boat: '02 Century 2600CC, twin Yamaha EFI 200's, full instruments.
Re: New boat expectations
My .02 since I repair/rebuild/modify...just because
Screws into alum tube be it 6061/6063 is a crap shoot, they use small screws to try to get 2 or 3 teeth engagement...that sucks and is B/S.
5 ways to do it is
Weld , but can stress crack
Rivet, but can stretch making them loose
Through bolt with NO spacer to not squish tube which will loosen
Through bolt with spacer, just a pain to position and make...or buy then cut to length to fit inside tubing
Best bet? Rivnuts, spend the $80 for correct tool, buy riv nuts and got to town, make sure to use antisieze for aluminum and different size riv nuts use different install tools...AND DO NOT OVER TIGHTEN you can snap off 1/4-20 SS screws easy
Screws into alum tube be it 6061/6063 is a crap shoot, they use small screws to try to get 2 or 3 teeth engagement...that sucks and is B/S.
5 ways to do it is
Weld , but can stress crack
Rivet, but can stretch making them loose
Through bolt with NO spacer to not squish tube which will loosen
Through bolt with spacer, just a pain to position and make...or buy then cut to length to fit inside tubing
Best bet? Rivnuts, spend the $80 for correct tool, buy riv nuts and got to town, make sure to use antisieze for aluminum and different size riv nuts use different install tools...AND DO NOT OVER TIGHTEN you can snap off 1/4-20 SS screws easy
Check out "Dudes" site www.whereisdude.com